When mixing vocals in Ableton, start with EQ and then compress with a quick attack and makeup gain to bring the vocal forward. With the dynamics controlled, introduce temporal processing like a chorus effect, various reverbs, and delays, before finishing the chain with slight compression and EQ.
For this video let’s create a complex vocal chain using only stock plugins. Also, we’ll do some demonstrations of the effects, starting more aggressive and then being dialed back to how I’d personally mix it.
For this vocal in particular, and in a lot of home recordings, there will be noise picked up in the background or from the electronics used. I’ll use a gate with a low threshold, quick attack, moderate release, some lookahead, and a high-pass internal side chain to attenuate it.
The noise was so quiet that a demonstration really isn’t needed, so let’s move on to the next insert.
Next, I’ll use 7 bands in total to cut out all frequencies below the fundamental with a high-pass, accent the fundamental and 2nd ordered harmonic with bells, dip some nasal tones, boost vocal presence around 3.5kHz, and boost air but balance sibilance with a shelf and bell respectively.
Let’s listen and notice how the vocal is clearer and more present.
Next, I’ll a compressor with peak detection to bring the vocal forward significantly. With a 5.5:1 ratio, the quickest attack possible, a release of 17.5ms, a hard knee, and 1ms of lookahead, the vocal is attenuated by about 3dB, as makeup gain retains the originally level.
As you’ll hear in a moment, by compressing the entirety of the vocal then bringing the signal back up, the vocal greatly moves forward. Let’s take a listen.
Now that the vocal is forward, I’m going to smooth out the dynamics a little more with the glue compressor. I’ll use a quicker attack, 4:1 ratio, and automatic release similar to an optical compression - then I’ll attenuate by a few dB, and makeup this change.
Let’s listen to how this compressor creates a full, slightly soft sound.
Tube saturation will introduce harmonic distortion to fill the sound, slightly emphasize the initial transient, and add a little warmth by emphasizing the 2nd order harmonic. I’ll increase the drive until I find what works best for the vocal, then blend the effect in with the Dry/Wet dial.
Let’s listen to the effect.
The chorus-ensemble plugin is going to duplicate the vocal cause mild timing modulations to these duplicates. I’ll select the ensemble option, ensure the lowest frequencies aren’t included, add a little warmth, and blend in the effect until I can no longer immediately tell it's there.
Let’s listen and notice how it makes the vocal thicker when used at low settings.
This is a unique plugin that’ll create multiple vocals and then tune them to a specific note. First, I’ll find a note that is in key with the vocal performance, I’ll adjust the number of voices, and then I’ll reduce the wet/dry until, like the chorus effect, it’s just barely noticeable.
Let’s listen to understand what this plugin does, and then how it sounds blended in.
A short reverb is going to thicken and fill out the vocal - this is especially true if those reflections are focused on the mids. I’ll reduce the room size, reduce the decay time, and then isolate the reflections to my mids and high mids while using high-quality processing.
With a shorter pre-delay, we’ll capture a good amount of the vocal, and the maxed-out density will help fill the vocal. Let’s listen to the effect.
Next, we’ll use the Hybrid Reverb to create a longer, more stylized effect on the vocals. I used a Hall impulse response, 50ms of pre-delay to let the transients pass unaffected, made the bass frequencies mono, and then blended in the effect to preference.
In the EQ section, I cut out the lowest frequencies and boosted presence and air.
A quick delay, after our stylized reverb, is going to duplicate the reflections, making that reverb more realistic and impressive. I’ll set my reflection time to a short one, isolate the reflections to the mids, enable mid/side reflections, and add some subtle modulation, before blending in the effect.
Let’s take a listen and pay attention to what this plugin does to the last reverb’s reflections.
I’m going to use one more compressor, but this time make it RMS to capture quicker parts of the vocal, mainly the temporal processing that we just introduced. With the internal sidechain, I’ll isolate the detection to the mids, use a soft knee, and achieve a few dB of attenuation.
I’ll again use auto-make-up gain to return the signal to its original level.
Let’s listen and notice how this pushes the reverb and other temporal effects forward.
Last up, I’m going to insert one more EQ to finalize the frequency balance of my vocal. I’ll keep this EQ simple and reduce the lows some of the temporal processing added, boost a little of the fundamental, add a little presence and a little more air.
Let’s listen to how this EQ finalizes the signal, and then let’s listen to a full AB of the vocal signal chain.
There are countless budget studios and AI software services claiming “instant audio-magic” — we do not offer these services.
We are not AI mastering. We are not SaaS (Software as a Service).
We are a long-standing audio engineering company staffed with seasoned professionals and have been providing professional audio engineering services for over two decades.
We listen to each client’s specific needs and then execute them with professional acumen.
We’re acutely focused on creating personalized results for each client’s specific needs, which can only be achieved with customized audio engineering services with personal working relationships.
If you’re not familiar with our company, review our studio and public history on Google here.
If you want to hear the quality of our work, review our portfolio here.
If you want to read certified reviews from customers who use our services, go here.
In short, we’re a niche audio engineering company that has stood the test of time, consistently providing personalized audio engineering services for over two decades.
If you’ve made it to this point in this letter and are looking for customized audio engineering services with personalized customer service specific to your needs — you’ve come to the right place.
SAGE AUDIO MEMBERSHIP$450 / month 67% Discount • Perpetual — Lock in your price before it increases
Unused masters accrue in your account — Additional masters can be purchased anytime
Unused consultations accrue in your account — Additional consultations can be purchased anytime
